precision.tube

EN 10305 series

EN 10305-4seamless cold drawn tubes for hydraulic and pneumatic lines

EN 10305-4 sets the technical delivery conditions for seamless cold drawn steel tubes of circular cross-section used in hydraulic and pneumatic power systems.1, 2 It is the tube that stockholders sell as hydraulic line tube, normalized and with a 3.1 inspection certificate.3, 4

Dwall thickness
Standard
EN 10305-4: Seamless cold drawn tubes for hydraulic and pneumatic power systems2
Tube
Seamless, cold drawn1
Purpose
Hydraulic and pneumatic power systems1
Cross-sections in scope
Circular1
Size limit in scope
None in the published scope summary1
Status
Current2
European edition
EN 10305-4:20161
German edition
DIN EN 10305-4:2016-082
Replaced in Germany
No DIN standard named5
Facts checked
20 November 2026
Sketch, not to scale. D is the specified outside diameter. The arrows stand for internal pressure in service.

What does EN 10305-4 cover?

As in the rest of the series, the tubes have precisely defined dimensional tolerances and a specified maximum surface roughness.1 The scope leaves the allowable pressure and temperature to the customer, who is to determine them in line with the state of the art and with the safety factors of the applicable regulations, codes or standards.1 For use at low temperatures, the scope points to impact energy requirements specified at 0 °C.1

DIN states that the tubes of Parts 4 and 6 are used for pressure equipment and that these standards are harmonized under the European Pressure Equipment Directive.6, 7 The Estonian standards body lists the Pressure Equipment Directive 2014/68/EU against EN 10305-4:2016.1 A note in the scope limits what this means: conformity with the directive’s essential safety requirements relates to the technical data of the material and does not establish that the material suits a particular item of equipment.1

The current edition is EN 10305-4:2016; the German version DIN EN 10305-4:2016-08 replaced DIN EN 10305-4:2011-04.1, 2 DIN describes the 2016 revision as mainly an update of references; for Parts 4 and 6 the requirements were also revised to reflect the needs of mechanical and vehicle engineering.2, 8

What is the difference between EN 10305-1 and EN 10305-4?

Both parts cover seamless cold drawn tubes of circular cross-section. Part 1 is the general document: its scope runs to 380 mm outside diameter and allows other cross-sections. Part 4 is written for tubes that serve as hydraulic and pneumatic lines: its scope makes the customer responsible for pressure and temperature limits and points to impact energy requirements at 0 °C, and DIN counts it among the standards harmonized under the Pressure Equipment Directive.1, 6, 9

EN 10305-1 and EN 10305-4 side by side
AttributePart 1Part 4
TubeSeamless, cold drawn9Seamless, cold drawn1
PurposeGeneral precision applications6Hydraulic and pneumatic power systems1
Cross-sections in scopeCircular; may also be applied to other cross-sections9Circular1
Size limit in scopeD ≤ 380 mm9, 10None in the published scope summary1
Scope addsNo such addition in the scope summary9, 10Pressure and temperature limits are for the customer to determine; impact energy is specified at 0 °C1
Pressure Equipment DirectiveNot named in DIN’s statement6Harmonized under the Pressure Equipment Directive, according to DIN6, 7
Delivery conditions in one stockholder’s listing+C, +N, +SR; others on request3+N3, 4
Current editionEN 10305-1:20169EN 10305-4:20161
StatusCurrent6, 9Current2

Data: CSV, JSON.

How is the tube supplied?

One European stockholder lists hydraulic and pneumatic line tube to Part 4 from 4 × 0.5 mm to 114.3 × 20 mm in steel grades E235 and E355 with a 3.1 inspection certificate; where the page states a delivery condition for these lines, it is +N.3 A German hydraulics supplier states that its EN 10305-4 tube series are delivered normalized (+N) as standard.4

Which editions have there been, and what came before?

Editions of EN 10305-4
German editionEuropean editionStatusReplaced
DIN EN 10305-4:2003-105EN 10305-4:2003WithdrawnNone named in DIN’s catalogue entry5
DIN EN 10305-4:2011-042, 5EN 10305-4:2011WithdrawnDIN EN 10305-4:2003-102, 5
DIN EN 10305-4:2016-082EN 10305-4:2016CurrentDIN EN 10305-4:2011-042

Data: CSV, JSON.

The first German edition of Part 4 was DIN EN 10305-4:2003-10. DIN’s catalogue entry names no earlier German standard that it replaced.5 DIN 2445-2:2000-09, which covers precision steel tubes for hydraulic systems from 100 to 500 bar under dynamic loads, is a separate standard and is still listed as current.12 Suppliers still pair the two: one German hydraulics supplier titles its product group ‘EN 10305-4 (DIN 2445/2)’.13

Is there an ASTM equivalent of EN 10305-4?

ASTM A822/A822M covers seamless cold-drawn carbon steel tubing for hydraulic system service where forming calls for tight-radius bending and flaring. Typical sizes run from 1/8 to 3 1/2 in (3.2 to 88.9 mm) outside diameter, and the tubing is heat treated after the final cold-working operation.14 SAE J524 covers cold drawn and annealed seamless low-carbon steel pressure tubing for hydraulic lines and other uses that need flaring and bending. SAE lists its latest issue, dated December 2025, as stabilized.15

Sources

  1. EVS, Estonian Centre for Standardisation and Accreditation. EVS-EN 10305-4:2016, catalogue entry with scope. evs.ee/en/evs-en-10305-4-2016 Checked 20 November 2026.
  2. DIN Media. DIN EN 10305-4:2016-08, catalogue entry with overview. dinmedia.de/en/standard/din-en-10305-4/251709296 Checked 20 November 2026.
  3. Van Leeuwen Pipe and Tube. Carbon steel precision tubes and bars, product listing. vanleeuwen.com/products/carbon-steel-precision-tubes-and-bars Checked 20 November 2026.
  4. HANSA-FLEX. Präzisionsrohr, EN 10305-4, nahtlos, Stahl E355+N, product page. shop.hansa-flex.de/de_DE/rohre/hydraulik-rohre/pr-st52-m/p/MAS_PR_ST52_%28M%29 Checked 20 November 2026.
  5. DIN Media. DIN EN 10305-4:2003-10 (withdrawn), catalogue entry. dinmedia.de/en/standard/din-en-10305-4/59298420 Checked 20 November 2026.
  6. DIN. DIN EN 10305-1:2016-08, standard entry with overview of the series. din.de/en/wdc-beuth:din21:251709111 Checked 20 November 2026.
  7. DIN Media. DIN EN 10305-6:2016-08, catalogue entry with overview. dinmedia.de/en/standard/din-en-10305-6/251709059 Checked 20 November 2026.
  8. DIN. DIN EN 10305-2:2016-08, standard entry. din.de/en/wdc-beuth:din21:251709396 Checked 20 November 2026.
  9. Intertek Inform. EN 10305-1:2016, catalogue entry with scope. shop.standards.ie/en-ie/standards/en-10305-1-2016-333477_saig_cen_cen_766266 Checked 20 November 2026.
  10. EVS, Estonian Centre for Standardisation and Accreditation. EVS-EN 10305-1:2016, catalogue entry with scope. evs.ee/en/evs-en-10305-1-2016 Checked 20 November 2026.
  11. DIN. DIN EN 10305-6:2016-08, standard entry with overview of the series. din.de/en/wdc-beuth:din21:251709059 Checked 20 November 2026.
  12. DIN Media. DIN 2445-2:2000-09, catalogue entry. dinmedia.de/en/standard/din-2445-2/31733867 Checked 20 November 2026.
  13. Landefeld. Precision-hydraulic tube, seamless, EN 10305-4 (DIN 2445/2), product group. landefeld.de/gruppe/en/precision-hydraulic-tube-seamless-en-10305-4-din-24452-/HR4X1 Checked 20 November 2026.
  14. ASTM International. ASTM A822/A822M-20, Standard Specification for Seamless Cold-Drawn Carbon Steel Tubing for Hydraulic System Service. store.astm.org/a0822_a0822m-20.html Checked 20 November 2026.
  15. SAE International. SAE J524_202512, Seamless Low-Carbon Steel Tubing Annealed for Bending and Flaring. saemobilus.sae.org/standards/j524_202512-seamless-low-carbon-steel-tubing-annealed-bending-flaring Checked 20 November 2026.

About this page

This page is generated from a graph of individual statements. Each statement carries its source and the date we checked it. Passages marked ‘Our reading’ are our own interpretation, with a stated confidence.

The page explains the standard and does not reproduce it. For design, ordering and inspection the standard itself is authoritative; it is sold by the national standards bodies. Supplier pages are cited as examples of trade practice, not as recommendations.

All statements and sources of this page as data: JSON.

About the author. Udo Bange has provided marketing support to companies in the steel tube and pipe industry for 25 years, among them Mannesmann, DMV, Europipe, the European Pipeline Research Group (EPRG), Gräbener Maschinentechnik and Standard-Metallwerke.